Quantity:
A Chipset Block Designed for the DFI LANParty UT NF4 SLI-DR Expert MotherboardFeatures:This chipset is specifically designed to fit the DFI LANParty UT NF4 SLI-DR Expert Motherboard. This block is designed to minimize any flow loss and provide lower temperatures on the chipset allowing HIGHER Overclocks!!!Includes: Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi
MPC-Chipset Block for Intel Loop MotherboardsFeatures:This chipset is designed to mount to Intel Motherboards with Loops.Mounts on boards with Center to Center Loop distances of 1.9" x 2.4" - 4 Loops (48.3mm x 61mm)nThe springs porvide about 5 lbs of force each (apporx 20lbs total force). Based on Danger Den measurements this meets/slightly exceeds the heat sink mounts. Danger Den does recommend a partial epoxy mix to prevent any movement or loop damage.Includes:Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi
MPC-Universal Chipset BlockFeatures:This chipset is designed to fit a broad range of motherboards. Fits most motherboards with hole spacings of 2.10" to 2.43" (53.3mm to 61.7mm)Includes:Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi
A Chipset Block Designed for the Asus A8N BoardFeatures:This chipset is specifically designed to fit the Asus A8N motherboares. This block is designed to minimize any flow loss and provide lower temperatures on the chipset allowing HIGHER Overclocks!!! Includes: Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi
Pre OrderNew - For the Intel Xpress 3200 (RD600)BoardsThe DD-3200i Chipset is designed to provide maximum cooling for the Intel Xpress 3200 chipset boards New Features: Compatible with Reference Design RD600 Xpress 3200 motherboards ( DFI only known one currently) 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi Includes:Complete Block Assembled with Top, and Gaskets High Flow G 1/4 1/2", 3/8", or 1/4" OD Fittings Low flow restriction low pressure drop Please leak test 24hrs upon receipt.
Pre OrderNew Chipset DesignFor the Intel BADAX 975X Boards!!Intel has done a great job on this chipset and it overclocks like a beast...You heard us right! Intel is teaching OVERCLOCKING!!!So for this monumental occassion, we have a block configured to fit the chipset so the FSB can be pushed to the limit.Features:100% copper 110 material Acrylic and brass top options Threaded fitting ports are G 1/4 BSPP for use with any similar spec fittings. Complete Block with O-Ring Pressure Tested to 50psi High flow 1/4", 3/8", or 1/2" Chrome Plated Fittings Machine lapped and flat mirror polished Stainless steel hold down Benefits:225 Heat Dissipating Columns for enhanced transfer of heat to the water and optimum coverage of the CPULow pressure drop design for maximum coolant flow rate Ready to install designed and tuned for your system for top performance Anti-Tarnish coating applied to prevent finger print or environmental changes. This specialized formula also has no affect on cooling potential. Corrosion will not occur when used with other Copper and Brass parts. Avoid using non-anodized aluminum (or all aluminum) if at all possible for maximum component life.
New Chipset Design For the NVIDIA 680i Boards!!The MPC-680i Chipset is designed to provide maximum cooling for the NVIDIA 680i chipset boardsFeatures:100% copper 110 material Acrylic and brass top options Threaded fitting ports are G 1/4 BSPP for use with any similar spec fittings. Complete Block with O-Ring Pressure Tested to 50psi High flow 1/4", 3/8", or 1/2" Chrome Plated Fittings Machine lapped and flat mirror polished Stainless steel hold downBenefits:225 Heat Dissipating Columns for enhanced transfer of heat to the water and optimum coverage of the CPULow pressure drop design for maximum coolant flow rate Ready to install designed and tuned for your system for top performance Anti-Tarnish coating applied to prevent finger print or environmental changes. This specialized formula also has no affect on cooling potential. Corrosion will not occur when used with other Copper and Brass parts. Avoid using non-anodized aluminum (or all aluminum) if at all possible for maximum component life.
New - For the Intel Xpress 3200 (RD600) BoardsThe DD-3200i Chipset is designed to provide maximum cooling for the Intel Xpress 3200 chipset boards New Features : Compatible with Reference Design RD600 Xpress 3200 motherboards (DFI only known one currently) 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi Check out our forums for additional overclocking info! Includes:Complete Block Assembled with Top, and Gaskets High Flow G 1/4 1/2", 3/8", or 1/4" OD Fittings and additional SLI Fitting Low flow restriction low pressure drop Please leak test 24hrs upon receipt. Options:Fitting Size Note: A full graphic installation guide by ourselves can be found here
New - For the NVIDIA 680i Boards!!The DD-680i Chipset is designed to provide maximum cooling for the NVIDIA 680i chipset boards New Features: Compatible with Reference Design 680i motherboards 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi Check out our forums for additional overclocking info! Includes:Complete Block Assembled with Top, and Gaskets High Flow G 1/4 1/2", 3/8", or 1/4" OD Fittings and additional SLI Fitting Low flow restriction low pressure drop Please leak test 24hrs upon receipt.Note: A full graphic installation guide by ourselves can be found here
New - For the Intel BADAX 975X Boards!! Get the watercooling parts displayed at QUAKECON! Intel has done a great job on this chipset and it overclocks like a beast...You heard us right! Intel is teaching OVERCLOCKING!!!So for this monumental occassion, we have a block configured to fit the chipset so the FSB can be pushed to the limit. Includes:Intel 975X chipset block 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psi Note: A full graphic installation guide by ourselves can be found here
This chipset is specifically designed to fit the Asus A8N motherboares. This block is designed to minimize any flow loss and provide lower temperatures on the chipset allowing HIGHER Overclocks!!! Includes: Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psiNote: A full graphic installation guide by ourselves can be found here
This chipset is specifically designed to fit the DFI LANParty UT NF4 SLI-DR Expert Motherboard. This block is designed to minimize any flow loss and provide lower temperatures on the chipset allowing HIGHER Overclocks!!! Includes: Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psiNote: A full graphic installation guide by ourselves can be found here
This chipset is designed to fit a broad range of motherboards. Fits most motherboards with hole spacings of 2.10" to 2.43" (53.3mm to 61.7mm) Includes: Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psiNote: A full graphic installation guide by ourselves can be found here
This chipset is designed to mount to Intel Motherboards with Loops.Mounts on boards with Center to Center Loop distances of 1.9" x 2.4" - 4 Loops (48.3mm x 61mm)nThe springs porvide about 5 lbs of force each (apporx 20lbs total force). Based on Danger Den measurements this meets/slightly exceeds the heat sink mounts. Danger Den does recommend a partial epoxy mix to prevent any movement or loop damage. Includes: Complete Block Assembled with Top and O-ring 100% Copper 110 High Flow 1/2" or 3/8" OD Fittings Stainless Steel Hold Down Machined Lapped and polished beyond 1200 grit Pressure tested before shipment to 85psiNote: A full graphic installation guide by ourselves can be found here
